View LTST-C295KGKSKT_1883555.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y features * meet rohs, green product. * dual color chip led. * ultra bright alingap chip led. * package in 8mm tape on 7" diameter reels. * compatible with automatic placement equipment. * compatible with infrared reflow solder process. * eia std package. * i.c. compatible. package dimensions devices part no. lens source color pin assignment alingap green 1,3 LTST-C295KGKSKT water clear alingap yellow 2,4 notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.10 mm (.004") unless otherwise noted. part no. : LTST-C295KGKSKT page : 1 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at ta=25 c LTST-C295KGKSKT parameter green yellow unit power dissipation 75 75 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 80 80 ma dc forward current 30 30 ma reverse voltage 5 5 v operating temperature range -30 c to + 85 c storage temperature range -40 c to + 85 c infrared soldering condition 260 c for 5 seconds part no. : LTST-C295KGKSKT page : 2 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y suggestion profile: suggestion ir reflow profile for pb free process r e c o m m e n d e d p r o file b e t w e e n a s s e m b le a n d h e a t-r e s is t a n c e l in e t h e p r o file is a v a ila b le th a t m u s t to u s e s n a g c u s o ld e r p a s t e part no. : LTST-C295KGKSKT page : 3 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at ta=25 c LTST-C295KGKSKT parameter symbol green yellow unit test condition min. 18.0 28.0 typ. - - luminous intensity iv max. 112.0 180.0 mcd if =20ma note 1 viewing angle 2 q 1/2 typ. 130 130 deg note 2 (fig.6) peak emission wavelength l p typ. 574 591 nm measurement @peak (fig.1) dominant wavelength l d typ. 571 589 nm if =20ma note 3 spectral line half-width dl typ. 15 15 nm typ. 2.0 2.0 forward voltage vf max. 2.4 2.4 v if =20ma vr = 5v reverse current ir max. 10 10 m a vr = 5v notes: 1. luminous intensity is measured with a lig ht sensor and filter combination that approximates the cie eye-response curve. 2. 1/2 is the off-axis angle at which the luminous int ensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. caution in esd: static electricity and surge damages the led. it is recommend to use a wrist band or anti-electrostati c glove when handling the led. all devices, equipment and machinery must be properly grounded. part no. : LTST-C295KGKSKT page : 4 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : LTST-C295KGKSKT page : 5 of 1 1 bns-od-c131/a4 bin code list luminous intensity color : green , unit : mcd @20ma bin code min. max. m 18.0 28.0 n 28.0 45.0 p 45.0 71.0 q 71.0 112.0 tolerance on each intensity bin is +/-15% luminous intensity color : yellow , unit : mcd @20ma bin code min. max. n 28.0 45.0 p 45.0 71.0 q 71.0 112.0 r 112.0 180.0 tolerance on each intensity bin is +/-15%
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 c ambient temperature unless otherwise noted) part no. : LTST-C295KGKSKT page : 6 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y cleaning do not use unspecified chemical liquid to clean led they could harm the package. if clean is necessary, immerse the led in ethy l alcohol or in isopropyl alcohol at normal tempera ture for less one minute. suggest soldering pad dimensions package dimensions of tape and reel notes: 1. all dimensions are in millimeters (inches). part no. : LTST-C295KGKSKT page : 7 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y notes: 1. empty component pockets sealed with top cover ta pe. 2. 7 inch reel-4000 pieces per reel. 3. minimum packing quantity is 500 pcs for remainde rs. 4. the maximum number of consecutive missing lamps is two. 5. in accordance with ansi/eia 481-1-a-1994 specifi cations. part no. : LTST-C295KGKSKT page : 8 of 1 1 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : LTST-C295KGKSKT page : 9 of 1 1 bns-od-c131/a4 cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household ap plications).consult liteons sales in advance for information on applications in which exceptiona l reliability is required, particularly when the fa ilure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation , traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original p ackaging are ir-reflowed within one week. for extended storage out of their original packagin g, it is recommended that the leds be stored in a sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient. leds stored out of their original packaging for mor e than a week should be baked at about 60 deg c for at least 24 hours before solder assembly. 3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the led if necessary. 4. soldering recommended soldering conditions: reflow soldering soldering iron pre-heat pre-heat time peak temperature soldering time 120~150c 120 sec. max. 260c max. 5 sec. max.(two times only) temperature soldering time 300c max. 3 sec. max. (one time only) 5. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connected in parallel in an application, it is reco mmended that a current limiting resistor be incorpo rated in the drive circuit, in series with each led as sh own in circuit a below. circuit model a circuit model b led led (a) recommended circuit. (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds. 6. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use of a conductive wrist band or anti-electrostati c glove when handling these leds. all devices, equipment, and machinery must be prope rly grounded. work tables, storage racks, etc. should be properly grounded. use ion blower to neutralize the static charge whic h might have built up on surface of the leds plastic lens as a result of friction between leds d uring storage and handling.
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : LTST-C295KGKSKT page : 10 of 11 bns-od-c131/a4 esd-damaged leds will exhibit abnormal characterist ics such as high reverse leakage current, low forward voltage, or no lightup at low currents. to verify for esd damage, check for lightup and vf of the suspect leds at low currents. the vf of good leds should be >2.0v@0.1ma for i ngan product and >1.4v@0.1ma for alingap product. 7. reliability test classification test item test condition reference standard operation life ta= under room temperature as per data sheet maximum rating * test time= 1000hrs (-24hrs,+72hrs)*@20ma. mil-std-750d:1026 (1995) mil-std-883d:1005 (1991) jis c 7021:b-1 (1982) high temperature high humidity storage ir-reflow in-board, 2 times ta= 655 ,rh= 90 95% * test time= 240hrs2hrs mil-std-202f:103b(1980) jis c 7021:b-11(1982) high temperature storage ta= 1055 * test time= 1000hrs (-24hrs,+72hrs) mil-std-883d:1008 (1991) jis c 7021:b-10 (1982) endurance test low temperature storage ta= -555 * test time=1000hrs (-24hrs,+72h rs) jis c 7021:b-12 (1982) temperature cycling 105 25 -55 25 30mins 5mins 30mins 5mins 10 cycles mil-std-202f:107d (1980) mil-std-750d:1051(1995) mil-std-883d:1010 (1991) jis c 7021:a-4(1982) thermal shock ir-reflow in-board, 2 times 85 5 -40 5 10mins 10mins 10 cycles mil-std-202f:107d(1980) mil-std-750d:1051(1995) mil-std-883d:1011 (1991) solder resistance t.sol= 260 5 dwell time= 10 1secs mil-std-202f:210a(1980) mil-std-750d:2031(1995) jis c 7021:a-1(1982) ir-reflow ramp-up rate(183 to peak) +3 / second max temp. maintain at 125(25) 120 seconds max temp. maintain above 183 60-150 seconds peak temperature range 235 +5/-0 time within 5c of actual peak temperature (tp) 10-30 seconds ramp-down rate +6 /second max mil-std-750d:2031.2(1995) j-std-020(1999) environmental test solderability t.sol= 235 5 immersion time 20.5 sec immersion rate 252.5 mm/sec coverage R 95% of the dipped surface mil-std-202f:208d(1980) mil-std-750d:2026(1995) mil-std-883d:2003(1991) iec 68 part 2-20 jis c 7021:a-2(1982) 8. others the appearance and specifications of the product ma y be modified for improvement without prior notice.
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y 9. suggested checking list training and certification 1. everyone working in a static-safe area is esd- certified? 2. training records kept and re-certification dat es monitored? static-safe workstation & work areas 1. static-safe workstation or work-areas have esd signs? 2. all surfaces and objects at all static-safe wo rkstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sens itive (esds) items wears wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibrati on up to date? note: *50v for blue led. device handling 1. every esds items identified by eia-471 labels on item or packaging? 2. all esds items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. no static charge generators (e.g. plastics) insi de shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycles? others 1. audit result reported to entity esd control coor dinator? 2. corrective action from previous audits completed ? 3. are audit records complete and on file? part no. : LTST-C295KGKSKT page : 11 of 11 bns-od-c131/a4

▲Up To Search▲

Price & Availability of LTST-C295KGKSKT

	To Download LTST-C295KGKSKT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .